Christmas arrives a little early for one of our customers as he has treated himself to a new tone arm on his Michell Gyro turntable. He had an ageing Rega RB300 previously installed on the turntable that was starting to become troublesome. With our advice the customer chose the obvious choice, the Michell Techno A tonearm in black to match the existing finish of the turntable.

Michell Gyro with new Techno A arm fitted

At the same time we have also removed the old acrylic plinth and lid giving the deck a much slicker look and feel. This was achieved by adding the Michell Gyro Spyder kit as shown below. The old deck is dismantled and the feet are removed from the plinth and threaded on to the new Spyder.

The old arm mounting plate needs to be replaced as it is the single mounting point plate. The new mounting plate is seen fitted in place above. The new three point mount all ready for the new tone arm.

Next we need to fit the cartridge to the tonearm. Our customer decided to go for the Rega Ania MC cartridge as shown below.

Now we need to adjust the height of the tonearm to make sure the vertical tracking angle is correct for the cartridge installed. This is achieved by the clever Michell thread at the mounting of the arm. In this case no adjustment was needed so the three mounting screws can tightened to fix the tonearm in place.

Michell Techno A arm Scallop counter weights

Two different weight scallops are supplied depending on the weight of your cartridge. In this case the larger of the two has been used.

Above we are checking the tracking weight using Project Measure IT stylus balance gage.

Cue up ready……”drop the needle on the record”

Above is the is older Michell HR power supply (this has now been replaced with a more modern looking box and case work) alongside the Nytech CDP122, our weapon of choice at the moment when it comes to supplying moving magnet or moving coil setups.

Thanks to Steve for his permission to blog about his latest audio upgrade. In the pic above we have the front of his home cinema setup. The classic Pioneer plasma, Arcam AVR550, REL S3, Oppo UDP-203 & the now discontinued Bowers & Wilkins 683S2 teamed with the HTM61S2 center speaker. He finishes off his surround system with two B&W M1 speakers on the rear and B&W CCM665 in the ceiling for Dolby Atmos, creating a very impressive 5.1.2 system. Michell Techno A arm and Rega ANIA MC cartridge is available from all branches of Audio T.

Michell Engineering turntables are available from the following branches of Audio T:
Brentwood, Cardiff, Manchester, Southampton, Swansea

Thanks for reading: Hefin, Nick (blogger) and Kerrin Audio T Cardiff.

We've never heard our demonstration room sound quite like this before... Dolby Atmos really does take home cinema to a new level. We have opted for x4 in-ceiling B&W CCM665's with the matching BB6C back boxes for maximum performance.

Pioneer's new top of the range Blu-ray player the BDP-LX88 feeds perfect picture & sound into Pioneer's power house AV Receiver the SC-LX88.

Dolby Atmos isn't the only thing that's caught our attention... REL's Shotgun 3D set up really is a must for any hardcore movie lover, the following paragraph has been taken from REL's website.

"For ultimate spatial coherence, a minimum of 3 RELs (1-main L/R, 1-center, 1-surrounds) may be used to fully realize all the performance embedded in movie soundtracks. REL Shotgun unleashes the basic performance possible in a soundtrack. Shotgun 3D™ extends that benefit to all the building blocks of a theater. By extending the low bass performance of the center channel the entire front half of the theater Is opened up. No longer does the center channel struggle to keep up with the mains. By doing so for the rear channels, the theater is completed and the 3 dimensional reality of film soundtracks takes place as one’s theater is transformed into a sort of 3 dimensional aural holograph."

We liked the sound of this, so have decided to order a custom centre stand from our friends at Hi-Fi racks to sit over a T-Zero, T-5, T-7 or S2. Not only does this look right, it aids with the timing between the centre channel & sub, which accounts for seamless integration with each other.

We're not sure whats more exciting, Dolby Atmos or REL's Shotgun 3D. What we are sure about, is that we've not heard better! We urge you to come down & have a listen to what we believe is the ultimate home cinema solution.

See and hear what you're missing today!

Please call or email us to arrange a demo

Best Wishes

Simon

Audio T

159a Chase Side

Enfield

EN2 0PW

Tel: 0208 367 3132

Email: enfield@audio-t.co.uk

Audio T Blogs

Michell My Belle! Customer Upgrades His Gyro Turntable With Michell Techno Tonearm

Dolby Atmos & REL 3D arrive at Audio T Enfield!

Audio T

Blogs by store